แฟนคอมพิวเตอร์มักจะทำงานที่ 100% เว้นแต่จะระบุไว้มิฉะนั้น?

สารบัญ:

วีดีโอ: แฟนคอมพิวเตอร์มักจะทำงานที่ 100% เว้นแต่จะระบุไว้มิฉะนั้น?

วีดีโอ: แฟนคอมพิวเตอร์มักจะทำงานที่ 100% เว้นแต่จะระบุไว้มิฉะนั้น?
วีดีโอ: Обзор Android P (Developer Preview 1) 2024, มีนาคม
แฟนคอมพิวเตอร์มักจะทำงานที่ 100% เว้นแต่จะระบุไว้มิฉะนั้น?
แฟนคอมพิวเตอร์มักจะทำงานที่ 100% เว้นแต่จะระบุไว้มิฉะนั้น?
Anonim
ไม่ว่าจะเป็นบนแล็ปท็อปเดสก์ท็อปหรือแม้แต่เกมคอนโซลเราก็ได้ยินเสียงโห่ร้องของแฟน ๆ ระบบในเบื้องหลัง แฟน ๆ ระบายความร้อนทั้งหมดเหล่านี้รู้หรือไม่ว่าเมื่อใดจะหมุนขึ้นลงและลดปริมาณอากาศที่พวกเขากำลังเคลื่อนที่?
ไม่ว่าจะเป็นบนแล็ปท็อปเดสก์ท็อปหรือแม้แต่เกมคอนโซลเราก็ได้ยินเสียงโห่ร้องของแฟน ๆ ระบบในเบื้องหลัง แฟน ๆ ระบายความร้อนทั้งหมดเหล่านี้รู้หรือไม่ว่าเมื่อใดจะหมุนขึ้นลงและลดปริมาณอากาศที่พวกเขากำลังเคลื่อนที่?

เซสชั่นคำถามและคำตอบในวันนี้มาถึงเราด้วยความอนุเคราะห์จากแผนก SuperUser ของ Stack Exchange ซึ่งเป็นกลุ่มของ Q & A ที่เป็นชุมชนที่ขับเคลื่อนด้วยชุมชน

คำถาม

ผู้อ่าน SuperUser darkAsPitch มหัศจรรย์:

What happens if I do not plug it into the motherboard and it does not have a switch?

I have seen fans before with an “off/low/high” switch that allows you to manually set their speed.

I have seen fans that plug into the motherboard and are controlled by the OS.

I am curious… what does a fan do by default when plugged into a PSU? Does it run at 100% unless otherwise told to go slower? This is what I would expect…

ดังนั้นพวกเขาจึงทำงานอย่างไร เจาะลึกเว้นแต่ได้รับคำสั่งเป็นอย่างอื่นหรือไม่?

คำตอบ

ผู้สนับสนุน SuperUser Journeyman Geek เสนอข้อมูลเชิงลึกต่อไปนี้:

Well, kind of. Fan speed control is done by varying voltage or through Pulse Width Modulation (using a constant voltage and cutting it up into pulses to vary speed). If you’re plugged into a motherboard, that’s what it does. If it has 3 wires, the third wire tells the motherboard what’s the speed the fan is running as. If you have a 4th wire, fan speed control is done via PWM rather than voltage control.

You can plug in a 2 wire fan to a 3 or 4 wire connector (though you lose speed feed back), and a 3 wire to a 4 wire connector (where you lose PWM control). You can also use a fan controller to control speeds.

Else, assuming the power source is unaware it’s a fan (as it would be connected through molex for example), and is at a fixed voltage, yes, it goes at full speed all the time.

ผู้สนับสนุน Fellow Hyperslug ไฮไลท์ว่าข้อยกเว้นดังกล่าวมีการเล่นอย่างไร:

Like the other guys said, pretty much yes, but I can think of 3 exceptions:

1. A few fans have a built in thermistor that will adjust speed depending on temperature.

2. PSU’s with specially marked Fan-Only PSU connectors (Antec TruePower 550W) can adjust the speed of the fan:

3. If you plug it into the PSU molex using the 12/5 volt rails (7 volt) or 12/7 rails (5 volt) it’ll be run slower, but at this point you’re modding.
3. If you plug it into the PSU molex using the 12/5 volt rails (7 volt) or 12/7 rails (5 volt) it’ll be run slower, but at this point you’re modding.

และมีคุณอยู่นอกการควบคุมภายนอกโดยกลไกบางอย่าง (ไม่ว่าจะเป็นอินพุตของเมนบอร์ดเครื่องวัดอุณหภูมิกรณีหรือ PSU อัจฉริยะ) พัดลมจะทำงานด้วยความเร็วสูงสุดที่แหล่งจ่ายไฟจะอนุญาต

มีบางอย่างที่จะเพิ่มคำอธิบายหรือไม่? เสียงในความคิดเห็น ต้องการอ่านคำตอบเพิ่มเติมจากผู้ใช้ Stack Exchange ที่มีความเชี่ยวชาญด้านเทคโนโลยีหรือไม่? ดูหัวข้อการสนทนาฉบับเต็มได้ที่นี่

แนะนำ: